Anycubic Kossel Upgraded Pulley Version Unfinished 3D Printer

FAQ for Anycubic Kossel Upgraded Pulley Version Unfinished 3D Printer

• Does Anycubic Kossel 3D printer have auto leveling function?

  No, it doesn't have.

• Whether it has been assembled?

  No, you need to assemble it by yourself and you can refer to the video on the website.

• Does a computer have to be connected at all times while printing?

  You can print with SD card.

• Does it come with heatbed?

  There is no heatbed, you need to buy it( a circle heatbed with diameter 180mm ). Othewise, you can choose this one has heatbed: https://www.gearbest.com/3d-printers-3d-printer-kits/pp_1412320.html.

• What kind of mainboard does it applied?

  TriGorilla mainboard.

• Why the the heat end wouldn't heat up?

  1. Please test the heater ceramic cartridge, the resistance is 3.6Ω;

  2. Please heat the print head only (via control from screen), test heater 1 prot volt, it should be 12V;

  3. Please double check the wiring of thermistor, and the themistor resistance should be 25° 100KΩ.

• Why the LCD no power?

  1. Ensure the machine is well connected to the power / PC;

  2. Ensure the wiring of LCD is correct(EXP1 to EXP1; EXP2 to EXP2);

  3. Ensure the firmware has been uploaded. If not, LCD would show blank;

  4. Adjust the brightness by rotate the smaa "contrast" knob on the back of LCD.

• Why the motor is shaking or run opposite?

  Please check with the A4988 driver to see if the Al colling fin contacts with the pins. In this case, A4988 is very likely damaged and need change.

• The print head is shaking, what can i do?

  1. Ensure the screws on carbon fiber tubes are well connected;

  2. Ensure the clamp to fix the Al radiator is well fixed;

  3. Check belt tensioners, pulley carriages / linear rails and the corresponding screws.

• Can this item be shipped to my country?

  We can deliver orders to most countries. For a detailed explanation of each shipping method, destination and approximate delivery time, please check our website: https://www.gearbest.com/about/shipping-methods.html

• Why not extruding enough plastic?

  1. Incorrect filament diameter;

  2. Increase the extrusion multiplier.

  The solution to under-extrusion (not extruding enough plastic)

• Why there are holes and gaps in the top layers?

  1. Not enough top solid layers;

  2. Infill percentage is too low;

  3. Under extrusion.

  The detail you can read this post:

  Solutions to holes and gaps on the top surface during 3D printing

• How does 3D printer work?

  In fact, although there are many different brands of 3D printers, they all basic working principle is same: How does 3D printer work?

• How to debug the heatbed of 3D printer without auto leveling?

  There are many 3D printers that do not have automatic leveling,the platform leveling is very important. Let's talk about how to debug heating platform: How to debug 3D printer’s heating platform

• How to stop 3D prints from warping?

  When using a 3D printer, the first layer always fails to print, and warps when print several layers. It is really make people desperation, this post will help you to fix the problem: How to stop 3D prints from warping

• How to choose the right filament?

  When choosing a proper 3D printer filament, we need to consider the different features of its materials:

  Pick the right 3D printer filament

  3D printer filament comparison

• How to choose a 3D printer?

  We take a look at the key factors to consider when purchasing a 3D printer: 7 things you need to know before buying a 3D printer

• How to using Cura 3D slicing software?

  Cura is an open source 3D printer slicing application, it is widely used in 3D printing. Let's talk about how to install Cura 3D slicing software and operate it: Cura 3D slicing software installation and operation

• Why not extruding at start of print?

  1. Extruder was not primed before beginning the print;

  2. Nozzle starts too close to the bed;

  3. The filament has stripped against the drive gear;

  4. The extruder is clogged.

• Why the 3D printer always overheating?

  1. Insufficient cooling;

  2. Printing at too high of a temperature;

  3. Printing too fast;

  4. Try printing multiple parts at once.

• How to deal with the 3D printer nozzle jam?

  We will introduce a couple of single steps to help you dealing with this problem: How to deal with the 3D printer nozzle jam

• How to solve cracking or breaking of layers during 3D printing

  We will discuss some typical reasons and corresponding solutions: How to solve cracking or breaking of layers during 3D printing

• Why 3D printer details can not be printed out?

  There are several options that allow you to successfully print this subtle detail: Why 3D printer details can not be printed out?

• I want to print a large object, which 3D printer is better for me?

  We recommended the TEVO Black Widow 3D Printer Kit, because of it's large printing area (up to 370 x 250 x 300mm).

  The detail tips for choosing a 3D printer, you can read this post:

  3D Printer buying guide

• How to make my 3D-printed models look smooth and shining?

  Acetone Vapor is an easy way to smooth your ABS prints. Please check the specific steps in this guide:

  Acetone Vapor - A great way to make your 3D-printed models look smooth and awesome

• View More

Customer Questions

• All(27)
• Product Information(22)
• Stock Status(4)
• Payment
• About Shipping(1)
• Others