Xiaomi Mijia MJCTD01YL Yeelight Bedside Lamp FAQ

Not much power, only 10 watts.

The luminous flux is 300 lumens, which is equivalent to an incandescent lamp of about 40 watts.

 The service life is about 25000 hours.

Support touch control and APP software control.

100-240V～50/60Hz 0.5A

Yes, currently you can use Yeelight independent light control APP software in addition to the Xiaomi smart home APP control software.

At present, there are four kinds, one is a light-off mode, one is a white light mode, one is a color light mode, and the other is a streamer mode.

Yes, this bedside lamp supports sharing function and can connect multiple mobile phones. Currently there is no limit to the number.

Yes, there is no limit to the current number.

There is no limit to this distance. As long as both the mobile phone and the bedside light are in a network environment, they can be connected at will.

The connection distance is 30 meters or more (intermediate accessibility).

In the case of power-on, by turning on the key+mode key for 5 seconds at the same time, the light changes to red, green, and blue after two times, indicating that the reset was successful.

Yes, when new firmware is available, the bedside lamp can be upgraded via the "Check Firmware Update" button in the setup menu.

Yes, long press the key, until the light breathing effect, release the start delay light function, the default delay of 15 minutes after the lights off; can also use the APP control menu "delay light off" button on the bed The lamp is set to delay the lamp off time. The setting range is 1-60 minutes.

Support, you can set the time switch on the bedside lamp through the "Time Switch" button in the control menu.

No, it supports all brands of routers with wireless WiFi capabilities.

First, try resetting the bedside lights. The reset method is as follows: In the case of power-on, by turning on the key+mode key for 5 seconds at the same time, the light changes to red, green, and blue after two times, indicating that the reset was successful. Don't turn off the lights at this time. After the reset is successful, turn on the smart home app again. At this time, you will be automatically prompted to find the "m bedside light ****", then follow the prompts to install, but also pay attention to some environmental requirements:

1. The mobile phone and bedside light are both in WIFI connection and connected to the Internet.

2. The WIFI signal connected to the bedside lamp only supports 2.4G and does not support 5G.

3. The WIFI signal name of the router may not have Chinese characters.

4, if the mobile phone Android 4.4 and above systems, iOS 8 and above systems, with WiFi-enabled mobile phones.

5, look at the router's security level, if the level is set to high, there may be automatically shielded bedside lamp connection, you can set the router level is low, after a successful connection, and then set back.

 

1. Power supply is correctly connected (100-240V 50/60HZ 0.5A).

2. Is the adapter properly inserted into the power supply?

3. whether the adapter is correctly inserted into the bedside lamp power jack and good contact.

 

The process of connection requires data exchange between mobile phones, bedside lamps, routers, and cloud servers. The process is complex and prone to timeouts. There are several possible causes of connection timeout. The current possible scenarios are:

1. The network environment used by the product.

2. The adaptation of the mobile phone and the bedside lamp.

3. Adaptation of routers and bedside lights.

4. Data interaction with cloud servers.

5. The entered network password is incorrect.

When a timeout occurs, it is recommended to try several more times.

Mi's bedside lamps support the linkage of Green Rice's smart home suites, such as human sensors and wireless switches.

The bedside light supports Yeelight remote control, and the remote control is non-standard and needs to be purchased separately.

A: Keep the remote control and the bedside light in the same room, and then turn on the bedside light. After 60 seconds of power on, do the following operations, and press the remote control OFF+M key at the same time, the indicator of the remote control will flash , that is connected, waiting for the bedside lamp light red, green and blue after 3 times into white light, the connection is successful.

No, it can only be powered by the adapter.

0.8 watts.

The color temperature adjustment range is 1700K-6500K.