All
Product keywords
Please enter the email address account

Customer Reviews

4.25 out of 5
  • 1
  • 3
  • 0
  • 0
  • 0
Write a Review
  • Isaiah Barnes
    Yes (0) Color: White Size: EU Plug
    Read Full Review
    Very good price for its size.
    Easy to assemble.
    Solid and sturdy construction.
    Easy installation.

    Would recommend buying if you have the time and patience to properly calibrate it.
    I have bought this printer about a month ago as my first 3D printer. I would say big mistake, but I learned a lot from it.

    Shipping and Packaging: It arrived quicker than expected and was packaged securely and tightly wrapped with a very large amount of packaging tape, as the box looked a bit rough and worn. However the contents inside were secure in foam packaging, with no damage to the product.

    Assembly and Installation: It was very easy to assemble and did not take long to install to my computer. I followed the instructions exactly.
    Suggestion
    Instructions and help are a bit unclear and difficult in certain sections, but overall understandable.

    Auto-leveling is not reliable on its own. Manually level before auto-leveling for best results.

    Takes much time to calibrate and level.

    Issues: I tightened the belts as much as possible and used the auto-level function as instructed. For a while prints were coming off very off center, patchy, incomplete, and rough and I could not figure out what I was doing wrong. I talked to my high school engineering teacher and we spent about two weeks troubleshooting, testing and calibrating.

    The main issues were belt tension and rod length.

    The rods holding up the extruder head are supposed to be EXACTLY the same length, down to a hundredth of a millimeter. Two of the rods I received were just slightly shorter and threw off the accuracy, but eventually I positioned them so that it is no longer an issue.

    Though the instructions say the belts must be tight, it doesn't mean they should be as tight as possible. With the belts too tight, they stretch over time, and the tension causes considerable bounce, throwing off Z level accuracy.
    This issue was corrected by placing a piece of standard copy paper on the print bed, and then using gcode software to lower the print head to 0.1mm above the print bed at one edge closest to a set of guide rods. I then adjusted the belt tension slightly and gently pull on the paper, and repeat until there is just slight resistance on the paper, but not enough so that it is hard to pull. (tighten belt to raise head, loosen to lower) I then repeated the process with the other two sets of rails. Afterwards, I pressed auto-level, and started a test print. It came out perfect, save for being 0.4mm larger in scale to what the model was supposed to be, but this can easily be fixed by scaling the model down by 0.4mm in the slicing software.


    Overall great printer, but not recommended

    Mar 04,2018

  • Эдуард
    Yes (1) Color: White Size: EU Plug
    Дельта принтер
    Из нескольких принтеров из китая этот самый без проблемный ! Неплохо печатает практически сразу после сборки. Радует скорость печати .Нагрев стола быстрый.Меню русифицировано! В общем от принтера совсем не плохие впечатления ,особенно по сравнению с принтерами somars и медведем летающим !
    Suggestion
    Сетевой кабель в обрыве. Крепление блока питания сорвано (точнее совсем нет резьбы)

    Apr 03,2018

  • Piotr
    Yes (0) Color: White Size: EU Plug
    buy because it's great
    solid and strong construction. Accuracy of printing. speed. I recommend

    Nov 28,2018

  • Good printer for the price
    Yes (0) Color: White Size: EU Plug
    FLSUN 3D printers
    It's been discontinued so it doesn't matter what are the Pro's and the Cons. At time of writing this search for the QQ model one.
    Suggestion
    It's been discontinued so it doesn't matter.

    Jul 05,2018