16 Bit ADS1115 Module

- RED 205630801

ADC Development Board for Raspberry Pi 3B 2B B+ Zero
1 Notice Submitted
  • FREE SHIPPING Estimated Shipping Time: business days Order Processing Time may require a few days. Once dispatched from warehouse, Shipping (or Delivery) Time depends on the Shipping Method.
  • +
  • interest-free You can enjoy a maximum of 0 interest-free installments, and may not enjoy this offer when placing orders with other products
;   
Tax Info Price Protection Price Disclaimer
Clearance

Recommended Products for You

Customers Who Bought This Item Also Bought


16 Bit ADS1115 Module for Raspberry Pi 3B 2B B+ Zero

Main Features:
● The ADS1115 is a precision analog-to-digital converter ( ADC )
● Data are transferred via an I2C-compatible serial interface, four I2C slave addresses can be selected
● Operated from a single power supply at 3.3V
● Can be used to detect analog signal and convert it to digital signal
● You can attach a joystick or other analog sensor such as NTC, temperature, dust sensor and so on
Note:the board showed in the picture is not included in the package

Specification

General

Type: 16 Bit ADS1115 Module for Raspberry Pi 3B 2B B+ Zero

Weight and Size

Product weight: 0.015 kg
Package weight: 0.035 kg
Product Size(L x W x H): 6.50 x 3.00 x 1.50 cm / 2.56 x 1.18 x 0.59 inches
Package Size(L x W x H): 8.00 x 4.00 x 3.00 cm / 3.15 x 1.57 x 1.18 inches

Package Contents

Package Contents: 1 x ADS1115 Module

Product Safety Disclaimer:
We do not accept any responsibility or liability for misuse of this or any other product. All our products are extensively tested to comply with rigorous and strict QC standards. For certain products (e.g. toys, knives, etc.), we recommend proper supervision as we cannot be held liable for misuse or accidents.

Guess you like

FAQ for 16 Bit ADS1115 Module

  • I've plugged my Raspberry Pi in, but nothing is appearing on the screen. What's wrong?

    It is important that you connect your cables in the correct order, ensuring that the HDMI cable is plugged in before the power.
  • Only the red light on my Pi is on! Is it broken?

    1. Check that your SD card is inserted correctly into your Raspberry Pi.

    2. Check that your SD card contains the software required for the Raspberry Pi to boot.

  • Do I need another computer to use a Raspberry Pi?

    You don't need another computer to use a Raspberry Pi, as it's a computer in its own right. However, when you need to create new micro SD cards, you might need occasional access to another computer.
  • I've copied NOOBS to an SD card, but it gets stuck on the splash screen. What should I do?

    If NOOBS won't load once you have copied the files over, it may be that you have a corrupt SD card. If you've tried a different SD card and NOOBS still doesn't work, then you might want to try installing Raspbian directly.
  • I have a Raspberry Pi 3. Do I need a special power supply?

    For most uses, the original official power supply will be fine.
  • Why Raspberry Pi boot sequence failures?

    Unlike a PC, the Raspberry Pi does not have a BIOS, so without a working software image, it is stone-cold-dead. Without a working OS, and if the power supply works, the only thing guaranteed to happen is that the red power LED turns on. If an image at least starts to boot, then looking at the status LEDs and the HDMI monitor can provide some indication of where the boot process failed.
  • Rainbow screen, what can i do?

    The rainbow flash screen should only appear for about a second (good). If the boot process halts with the rainbow screen on the monitor (bad), there may be a power supply issue, or a kernel software problem.
  • Bad or missing SD card, what is the problem?

    Using a Raspberry Pi 2 as an example, if there is no activity on the monitor and if the red and green status LEDs stay lit and un-blinking after power up, the SD card may not be fully inserted, not detected properly, not flashed or not formatted correctly.
  • No WiFi networks found during discovery scan?

    The activity LED on the WiFi dongle provides minimal indication of WiFi activity. If No WiFi networks are found, and it is flashing normally, there is no WiFi reception. If not flashing at all, the power requirements of the WiFi dongle may be over 150 mA, too high for a Pi USB port, or over 300 mA on a Pi B+, 2, and later versions (unlikely).
  • Why local WiFi network not found?

    It may take one or two minutes to find all available WiFi networks. If the local network does not appear in the list, the WiFi portion of the local router may be down or disabled, reception may be bad, or the router may not be responding to WiFi discovery.
  • Can this item be shipped to my country?

    We can deliver orders to most countries. For a detailed explanation of each shipping method, destination and approximate delivery time, please check our website:

    GearBest shipping methods

    20 things you need to know when shopping on GearBest

    Short guide on tracking fees and shipping insurance on GearBest

    GearBest shipping memo: save money on delivery by choosing the best option

Customer Questions & Answers

  • All
  • Product Information
  • Stock Status
  • Payment
  • About Shipping
  • Others

Be the FIRST to Ask a Question. Want GB Points? Just Write a Review!

Be the FIRST to Ask a Question. Want GB Points? Just Write a Review!

Be the FIRST to Ask a Question. Want GB Points? Just Write a Review!

Be the FIRST to Ask a Question. Want GB Points? Just Write a Review!

Be the FIRST to Ask a Question. Want GB Points? Just Write a Review!

Be the FIRST to Ask a Question. Want GB Points? Just Write a Review!

0 Questions & Answers View All>

Sponsored Products Related to This Item

Customer Reviews

5 out of 5
  • 1
  • 0
  • 0
  • 0
  • 0
  • Carlos Feitoza Filho
    Very practical ADC
    Color:Red
    The product is very well done and quite practical to make prototypes that require an analog-to-digital converter. It arrives well packed in an anti-static "ziplock". It was developed to take advantage of the I2C interface of Raspberry PI and, as a "ready module", makes prototyping much simpler because it is not necessary to handle individual connections to the RPI (GPIO) connectors. The developer just needs to dock the module and start programming the software. I want to use this module to make prototypes in Free Pascal, using Lazarus directly in RPI

    The official product site is: https://wiki.52pi.com/index.php/RPI-ADS1115-ADC-Module_SKU:EP-0076
    Suggestion
    The ad on GearBest does not have a link to the official product website, which has important information about the product, including how to use it. The site is: https://wiki.52pi.com/index.php/RPI-ADS1115-ADC-Module_SKU:EP-0076

    Apr 21,2018

    Was this review helpful?

Your Recently Viewed Items

See personalized recommendations

New customer? Start here